Ferdinand Drobik

How-to guides · Carol

How to adjust a knitting pattern to your own gauge on iPhone

To knit a pattern in your own gauge, measure a washed swatch, then recalculate the stitch and row counts from the difference. This guide does it with the Measure Gauge, Convert Pattern and Adjust Pattern tools in Carol, a free iPhone app, which round to whole pattern repeats and show the deviation.

What you need

  • The gauge printed in the pattern, usually stitches and rows over 10 by 10 cm
  • The yarn and needles you plan to use, and enough yarn for a swatch of at least 15 by 15 cm
  • The stitch and row counts of each section you want to change, such as cast on, ribbing and body
  • Carol on your iPhone

Step by step

  1. Knit a swatch

    Knit it in the stitch pattern of the project and with the needles you plan to use, larger than 10 by 10 cm and better at least 15 by 15 cm, so you can measure in the middle. If the pattern is worked in the round, knit the swatch in the round too, because the density differs.

  2. Wash and block it

    Wash and dry the swatch exactly the way you will treat the finished piece, and let it dry flat without stretching it. Only then does it show its true size, since some yarns grow and others shrink.

  3. Measure your gauge in Carol

    Open the Tools tab and tap Measure Gauge, which guides you in four steps. In the third step, enter the stitches you counted, the width you measured, the rows you counted and the height you measured, taking them from the middle of the swatch and not from the distorted edges. Carol then shows Your Gauge as stitches and rows per 10 cm (per 4 in if you use inches), and Save as My Gauge keeps it for later.

  4. Find the gauge in the pattern

    Look at the start of the pattern for its gauge, often written as 20 stitches and 28 rows over 10 by 10 cm. Note the stitch and row counts of the section you want to change, for example the cast on.

  5. Convert single numbers

    For a quick check, open Tools and tap Convert Pattern. Fill in Pattern Gauge and Your Gauge (you can pick a saved swatch), then enter a stitch count under Value from the Pattern, and a row count if you like. Result (Stitches) shows the raw value for your gauge and candidate counts with the width each gives and its deviation; add Pattern repeat in stitches and Edge stitches to get counts that fit the repeat.

  6. Adjust a whole pattern

    To work through every section, tap Adjust Pattern under Tools. It takes six steps: describe the pattern, enter the pattern gauge, enter your gauge, add one section for each part (such as ribbing, body or yoke) with its stitches, optional rows, repeat and edge stitches, then look at the results and your plan. If a section has increases or decreases, enter them under Increases or decreases, and Carol converts them to your gauge as well.

  7. Choose the stitch counts

    For each section Carol lists candidate stitch counts with the width each one gives and the deviation in centimetres. Nothing is rounded silently: tap the candidate you want, and read the note under Check if a deviation is more than about 1 cm.

  8. Knit from your plan

    In the last step, Your Plan lists each section with its old and new stitches and rows. Tap Add as Project to get a project with a counter for each section, or Save Adjustment to keep the numbers.

Tips

  • Measure in the middle of the swatch, and count half stitches too, for example 21.5 stitches per 10 cm.
  • If the ratio of rows to stitches differs from the pattern by more than 10 percent, Carol notes that the fabric will look different and that slopes and curves run somewhat differently. A different needle may bring your gauge closer.
  • Carol does not read the pattern. You type in the numbers, the pattern stays with you on paper or as a PDF, and Carol saves only your own entries.

Questions

Should I change needle size or recalculate the pattern?

Either works. If your gauge is off, you can change the needle until the swatch matches, or recalculate the pattern to your swatch. Carol’s own advice is to change the needle or hook, or adjust the pattern to your swatch, because otherwise the measurements change. Carol keeps the measurements and works out the stitches and rows for your gauge.

Can an app convert a PDF knitting pattern to my gauge automatically?

Not in Carol. Convert Pattern and Adjust Pattern work on the numbers you enter from the pattern, section by section, and Carol does not rewrite the PDF. With a PDF, Carol highlights the numbers that apply to the size you choose.

Does gauge conversion work for increases and decreases?

In Carol it does. Adjust Pattern converts the increases, decreases and repeats of each section to your gauge, and shows the deviation so you can check that the result still fits.

How big should a gauge swatch be?

Larger than 10 by 10 cm and better at least 15 by 15 cm, so you can measure in the middle and not at the distorted edges. Carol suggests this size in its Measure Gauge tool and asks you to wash and block the swatch before measuring.